NS8-TB Ethernet Module Test Suite
[Interface signal]：Ethernet
[Interface mode]：UART serial port
[Size]： 27*27*2.8mm
[Working voltage]：3.0~5.5V
[Introduction]：The NS8-TB test kit comes with a USB-to-TTL circuit without the need for users to connect an external converter, and leads to reset and factory reset pins for external buttons for easy operation, and also connects the operating status indicator pins to external LEDs for users to observe the status.
| No. | Pin Functional | Description |
| 1 | GND | Common ground terminal, power supply negative terminal input; |
| 2 | NC | default floating; |
| 3 | NC | default floating; |
| 4 | NC | default floating; |
| 5 | NC | default floating; |
| 6 | NC | default floating; |
| 7 | GND | Common ground terminal, power supply negative terminal input; |
| 8 | GND | Common ground terminal, power supply negative terminal input; |
| 9 | GND | Common ground terminal, power supply negative terminal input; |
| 10 | GND | Common ground terminal, power supply negative terminal input; |
| 11 | NC | default floating; |
| 12 | NC | default floating; |
| 13 | NC | default floating; |
| 14 | NC | default floating; |
| 15 | TXD2 | The serial port sends data, only supports 3.3V TTL, if it is connected to 5V, level conversion is required; |
| 16 | RXD2 | The serial port receives data, only supports 3.3V TTL, if it is connected to 5V, level conversion is required; |
| 17 | NC | default floating; |
| 18 | NC | default floating; |
| 19 | GND | Common ground terminal, power supply negative terminal input; |
| 20 | GND | Common ground terminal, power supply negative terminal input; |
| 21 | VCC | Positive power input, supports 3-5.5V input, can be used with pin 22 at the same time; |
| 22 | VCC | Positive power input, support 3-5.5V input; can be used with pin 21 at the same time; |
| 23 | NC | default floating; |
| 24 | NC | default floating; |
| 25 | NC | default floating; |
| 26 | NC | default floating; |
| 27 | NC | default floating; |
| 28 | NC | default floating; |
| 29 | NC | default floating; |
| 30 | NC | default floating; |
| 31 | NC | default floating; |
| 32 | NC | default floating; |
| 33 | 485EN-2 | Serial port 2 RS485 enable pin, normally low, pulled high when sending data |
| 34 | NC | default floating; |
| 35 | NC | default floating; |
| 36 | 485EN-1 | Serial port 1RS485 enable pin, normally low, pulled high when sending data |
| 37 | NC | default floating; |
| 38 | NC | default floating; |
| 39 | NC | default floating; |
| 40 | NC | default floating; |
| 41 | SPDLED | Network port data indicator |
| 42 | LINKLED | Network port connection indicator |
| 43 | RX+ | Ethernet receives RX+ signal; |
| 44 | RX- | Ethernet receives RX-signal; |
| 45 | TX+ | Ethernet sends TX+ signal; |
| 46 | TX- | Ethernet sends TX-signal; |
| 47 | RESTORE | Reset pin, pull down for more than 5 seconds to take effect |
| 48 | TXD1 | The serial port sends data, only supports 3.3V TTL, if it is connected to 5V, level conversion is required; |
| 49 | RXD1 | The serial port receives data, only supports 3.3V TTL, if it is connected to 5V, level conversion is required; |
| 50 | NC | default floating; |
| 51 | NC | default floating; |
| 52 | NC | default floating; |
| 53 | 3.3V | Can output voltage 3.3V; |
| 54 | GND | Common ground terminal, power supply negative terminal input; |
| 55 | NC | default floating; |
| 56 | NC | default floating; |
| 57 | NC | default floating; |
| 58 | NC | default floating; |
| 59 | NRST | Module reset, pull down for more than 1ms to take effect |
| 60 | NET | Network connection indicator, output 2S square wave if the connection is successful |
| If the connection is unsuccessful, output a 1S rectangular wave, pull it high for 0.9S, and pull it low for 0.1S | ||
| 61 | NC | default floating; |
| 62 | NC | default floating |
| 63 | NC | default floating; |
| 64 | NC | default floating; |
| 65 | LINK1 | Serial port 1 data link indicator, UDP mode output low level; |
| In other modes, if the connection is successful, the output will be low level, and if there is no connection, the output will be high level; | ||
| 66 | DATA1 | Serial port 1 data indicator pin, output 50ms square wave when there is data interaction; |
| 67 | LINK2 | Serial port 2 data link indicator, UDP mode output low level; |
| In other modes, if the connection is successful, the output will be low level, and if there is no connection, the output will be high level; | ||
| 68 | DATA2 | Serial port 2 data indicator pin, output 50ms square wave when there is data interaction; |
| 69 | NC | default floating; |
| 70 | NC | default floating; |
| 71 | NC | default floating; |
| 72 | NC | default floating; |